Recent Posts

Pages: [1] 2 3 ... 10
1
General Discussion / Re: 585 HE -- Cases In Production --
« Last post by hubel585 on September 04, 2017, 07:58:26 PM »
Thanks

Here is case measurements for our 416 HE target case
made by necking our 585 HE big belted case.




Here is picture of 375 HE left,  416 HE next,  416 HSM on the right..




Here, tentative specs,  416 HSM case we are doing from bmg brass,





A  375  HE,  with Lawton action, few are being done with those,Ed .....


2
Your Firearm Projects / Re: 12ga,10ga,8ga,4ga FH; 585HE/700HE; Big Bores---
« Last post by hubel585 on September 04, 2017, 07:56:21 PM »
Here is case measurements for our 416 HE target case
made by necking our 585 HE big belted case.




Here is picture of 375 HE left,  416 HE next,  416 HSM on the right..




Here, tentative specs,  416 HSM case we are doing from bmg brass,





A  375  HE,  with Lawton action, few are being done with those,Ed .....


3
AR45 Discussions / Re: Fitting a blow back bolt ejector to a lower
« Last post by Mad Machinist on August 16, 2017, 04:06:23 PM »
Colt pattern blowback upper isn't compatible with a CNC AR45 lower. Mag sits too low in the magwell and no where to put a feed ramp.....I DO have something in the works as far as blowback....just short handed and not enough machines...... ;) we are working on it.... However the DI45 runs exceptionally well .... www.maconarmory.com
4
Pistol Discussions / Re: How to get beretta 92fs blueprint?
« Last post by FUBob on August 12, 2017, 10:23:02 PM »
The frame is available in the downloads section of the main site - under Solid Model *.igs files, I have attached it to this post for you.
Hope this helps.
FUBob


Edit:  Can somebody recommend a .igs file viewer that allows you to get dimensions from please?
Thanks
5
General Discussion / Re: 585 HE -- Cases In Production --
« Last post by FUBob on August 12, 2017, 09:47:42 PM »
Enjoy reading your posts  :)
6
AR45 Discussions / Fitting a blow back bolt ejector to a lower
« Last post by dude47jp on August 09, 2017, 06:51:19 AM »
I see glock magazine 45acp lowers fitted with the ejector for a blow back bolt system.
Any body done this with a cnc lower, and have machinist spec ?
Thanks, Jim
7
AR45 Discussions / Re: 460 Rowland upper.
« Last post by dude47jp on August 09, 2017, 06:45:09 AM »
I had RMW make me a 460 Rowland barrel and built a upper.
Worked fine on a cnc lower
8
General Discussion / Re: 585 HE -- Cases In Production --
« Last post by hubel585 on July 23, 2017, 07:07:17 PM »
The 12ga FH case  now is in the new COTW book on
last  page in the wildcat section, I think page 324.
They gave good credit to Rob for the idea of that   case....


The model 416 HE long case in middle, hydro formed one,

has case capacity of 240 gr, and the 416 HSM in picture,

on the right, we fired a case twice, capacity is 320gr.. Ed..




More info out now;  short, fat cases sticking, pockets not lasting as expected.
Trying to get best speeds the things raising pressures are bad case
 proportions, too sharp of shoulders, too fast of powders...........
 and  debth of  the bullet into the powder space, as shown in the picture  below..
My 375, 416, etc testing, bullets loaded like bottom one, in longer freebore....Ed.


9
Your Firearm Projects / Re: 12ga,10ga,8ga,4ga FH; 585HE/700HE; Big Bores---
« Last post by hubel585 on July 23, 2017, 07:06:03 PM »
The 12ga FH case  now is in the new COTW book on
last  page in the wildcat section, I think page 324.
They gave good credit to Rob for the idea of that   case....


The model 416 HE long case in middle, hydro formed one,

has case capacity of 240 gr, and the 416 HSM in picture,

on the right, we fired a case twice, capacity is 320gr.. Ed..




More info out now;  short, fat cases sticking, pockets not lasting as expected.
Trying to get best speeds the things raising pressures are bad case
 proportions, too sharp of shoulders, too fast of powders...........
 and  debth of  the bullet into the powder space, as shown in the picture  below..
My 375, 416, etc testing, bullets loaded like bottom one, in longer freebore....Ed.


10
General Discussion / Re: 585 HE -- Cases In Production --
« Last post by hubel585 on June 26, 2017, 04:55:44 PM »
Guys asking about strong economical bolt gun to use for  28ga and
410 ga and  32ga with brass cases and higher pressures than plastic cases.
They can use a MN bolt action, here is pic of one with
our 585 case in the action.Guys can get  Magtech brass cases or have
 RMC make them....Guys can make 32ga case from 500 NE,
410s from 9.3 x 74 brass, etc..



Here is picture of our 416 HSM case sectioned next to original
BMG case on the right sectioned, to show that we still have
enough thickness in the sides to handle  high pressure,
in a case with 310 gr capacity..We are getting the wildcatting
work set up so we can do at least hundred a month.
We have lots of 585s,  375HEs,  416 HEs,  408 HEs.....
And working toward getting 416 HSMs in big numbers.



Here's comparison of  416 target cases, 1st  416 HE,  have whole bunch.
Second is model of what I'd have made  on  medium machine, if I could, 
the 416 HE Long. It has capacity of  230gr..
Third is our 416 HSM which we are working on making by wildcatting bmg
cases, And if  had run long cases, make longer 375 HE necking down 416 ..




Bryan Litz just recently shot 3 shot group at 2 miles using Paul
 Phillips heavy barreled, target rifle built by Lethal Precision in 
375 Lethal Mag(585HE necked down, very  similiar to 375HE )...
 It grouped 17.5 inches tall by 22 inches wide.

Applied Ballistics shooter Mitch Fitzpatrick just hit 3 of 5 at 3520 yards,
 weekend 10-13th  at Valdina Ranch , west of San Antonio.
Also used the 375 LM case similar to our 375 HE
Great shooting at the 2017 World's Longest Shot Challenge. Ed
Pages: [1] 2 3 ... 10