Recent Posts

Pages: [1] 2 3 ... 10
1
General Discussion / Re: 585 HE -- Cases In Production --
« Last post by hubel585 on July 23, 2017, 07:07:17 PM »
The 12ga FH case  now is in the new COTW book on
last  page in the wildcat section, I think page 324.
They gave good credit to Rob for the idea of that   case....


The model 416 HE long case in middle, hydro formed one,

has case capacity of 240 gr, and the 416 HSM in picture,

on the right, we fired a case twice, capacity is 320gr.. Ed..




More info out now;  short, fat cases sticking, pockets not lasting as expected.
Trying to get best speeds the things raising pressures are bad case
 proportions, too sharp of shoulders, too fast of powders...........
 and  debth of  the bullet into the powder space, as shown in the picture  below..
My 375, 416, etc testing, bullets loaded like bottom one, in longer freebore....Ed.


2
Your Firearm Projects / Re: 12ga,10ga,8ga,4ga FH; 585HE/700HE; Big Bores---
« Last post by hubel585 on July 23, 2017, 07:06:03 PM »
The 12ga FH case  now is in the new COTW book on
last  page in the wildcat section, I think page 324.
They gave good credit to Rob for the idea of that   case....


The model 416 HE long case in middle, hydro formed one,

has case capacity of 240 gr, and the 416 HSM in picture,

on the right, we fired a case twice, capacity is 320gr.. Ed..




More info out now;  short, fat cases sticking, pockets not lasting as expected.
Trying to get best speeds the things raising pressures are bad case
 proportions, too sharp of shoulders, too fast of powders...........
 and  debth of  the bullet into the powder space, as shown in the picture  below..
My 375, 416, etc testing, bullets loaded like bottom one, in longer freebore....Ed.


3
General Discussion / Re: 585 HE -- Cases In Production --
« Last post by hubel585 on June 26, 2017, 04:55:44 PM »
Guys asking about strong economical bolt gun to use for  28ga and
410 ga and  32ga with brass cases and higher pressures than plastic cases.
They can use a MN bolt action, here is pic of one with
our 585 case in the action.Guys can get  Magtech brass cases or have
 RMC make them....Guys can make 32ga case from 500 NE,
410s from 9.3 x 74 brass, etc..



Here is picture of our 416 HSM case sectioned next to original
BMG case on the right sectioned, to show that we still have
enough thickness in the sides to handle  high pressure,
in a case with 310 gr capacity..We are getting the wildcatting
work set up so we can do at least hundred a month.
We have lots of 585s,  375HEs,  416 HEs,  408 HEs.....
And working toward getting 416 HSMs in big numbers.



Here's comparison of  416 target cases, 1st  416 HE,  have whole bunch.
Second is model of what I'd have made  on  medium machine, if I could, 
the 416 HE Long. It has capacity of  230gr..
Third is our 416 HSM which we are working on making by wildcatting bmg
cases, And if  had run long cases, make longer 375 HE necking down 416 ..




Bryan Litz just recently shot 3 shot group at 2 miles using Paul
 Phillips heavy barreled, target rifle built by Lethal Precision in 
375 Lethal Mag(585HE necked down, very  similiar to 375HE )...
 It grouped 17.5 inches tall by 22 inches wide.

Applied Ballistics shooter Mitch Fitzpatrick just hit 3 of 5 at 3520 yards,
 weekend 10-13th  at Valdina Ranch , west of San Antonio.
Also used the 375 LM case similar to our 375 HE
Great shooting at the 2017 World's Longest Shot Challenge. Ed
4
Your Firearm Projects / Re: 12ga,10ga,8ga,4ga FH; 585HE/700HE; Big Bores---
« Last post by hubel585 on June 26, 2017, 04:54:00 PM »
Guys asking about strong economical bolt gun to use for  28ga and
410 ga and  32ga with brass cases and higher pressures than plastic cases.
They can use a MN bolt action, here is pic of one with
our 585 case in the action.Guys can get  Magtech brass cases or have
 RMC make them....Guys can make 32ga case from 500 NE,
410s from 9.3 x 74 brass, etc..



Here is picture of our 416 HSM case sectioned next to original
BMG case on the right sectioned, to show that we still have
enough thickness in the sides to handle  high pressure,
in a case with 310 gr capacity..We are getting the wildcatting
work set up so we can do at least hundred a month.
We have lots of 585s,  375HEs,  416 HEs,  408 HEs.....
And working toward getting 416 HSMs in big numbers.



Here's comparison of  416 target cases, 1st  416 HE,  have whole bunch.
Second is model of what I'd have made  on  medium machine, if I could, 
the 416 HE Long. It has capacity of  230gr..
Third is our 416 HSM which we are working on making by wildcatting bmg
cases, And if  had run long cases, make longer 375 HE necking down 416 ..




Bryan Litz just recently shot 3 shot group at 2 miles using Paul
 Phillips heavy barreled, target rifle built by Lethal Precision in 
375 Lethal Mag(585HE necked down, very  similiar to 375HE )...
 It grouped 17.5 inches tall by 22 inches wide.

Applied Ballistics shooter Mitch Fitzpatrick just hit 3 of 5 at 3520 yards,
 weekend 10-13th  at Valdina Ranch , west of San Antonio.
Also used the 375 LM case similar to our 375 HE
Great shooting at the 2017 World's Longest Shot Challenge. Ed
5
I just wanted to pass on a great experience I had from Mounting Solutions Plus. I ordered fixed Samson irons for my Macon Armory upper. The sights are amazing but I was very impressed with their customer service. It was out of stock but they went out of their way to keep me informed with status, even offering to substitute. I was dead set on my choice. The wait was very reasonable. Shipping was prompt. And best of all, they had the best price I could find!

http://www.mountsplus.com/AR-15_Accessories/AR-15_Scope_Rings/SMC-P-FXF-FXR.html
6
General Discussion / Need CNC Milling Help for 80% Lower
« Last post by intz2nu on June 14, 2017, 09:53:40 PM »
Does anyone here work with CamBam and Mach3? I'm in need of some assistance with milling a lower out for the first time on a small CNC mill that I have. This is my first CNC mill and I'm currently having issues with my Z axis going beyond its limit of travel.

I will gladly pay someone for their time if they feel they could help me out with my issue(s) and also if they would feel comfortable walking me through over the phone. PM me if you think you could be of a help.


Thanks.
7
Pistol Discussions / How to get beretta 92fs blueprint?
« Last post by ActorS on May 29, 2017, 11:56:03 PM »
Where can I get to beretta 92fs blueprint?

I need it, who can tell me.

thank you very much. :)
8
AR45 Discussions / Re: MP5/ AR .45 project
« Last post by Baltimoreed11754 on May 15, 2017, 08:06:42 AM »
Here's a pix of the rifle rear sight on it. Couldn't get low enough to use the MP5 sight easily. Added a piece of the rear plate with a cutout for the gas key. Even though it's blowback the key is needed for the foward charging handle. Shoots great, very reliable but I need to alumahyde it.
9
AR10 Discussions / Re: has anyone ever gotton ahold of a dpms .308 cad file?
« Last post by Carnage on May 03, 2017, 07:41:38 AM »
I've release all my print for AR15 and .308 DPMS Compatible AR, you can get it at http://www.ssidefense.com/tag/308/
I'll be releasing .308 GEN 2 compatible models soon
10
General Discussion / Re: 585 HE -- Cases In Production --
« Last post by hubel585 on April 25, 2017, 04:30:48 PM »
Here is picture of a brake on 12ga FH with real hot loaded
hollowbase lead slug, brake needed more clearance
for  the expanding slug.




Here is the  before and after of  375 HE cases,   
 2 on left necked,  2 on right formed in hydro die after necking..



Here is pic of 416 HSM second from left we are experimenting
with, going to see if we can make the ultimate 416 ELR case.
Can be 3.60" to 4.00" long, a long one pictured.
Holds over  280 gr ball powder under bullet. In the picture,
1st case is 416 HE, 2nd 416 HSM, 3rd 375 HE, 4th 378 WEA.

416 HSM will get 400gr to 4100 plus without needing BMG action,
470 gr 3800 plus , it may be the ultimate target, singleshot 416..
Case will work in fat bolt actions, with heavy enough barrel
to have good, milder, barrel harmonics and srtill  be under 50 lbs.
A lot of the 2 mile type shoots are adopting 50lb limit.



Here is picture of  the 416 HSM fireformed once,
next to bmg case we make it from and as we
improve wildcatting process next few weeks
some specs may make small changes, now from
base to shoulder is 3.45", case 3.97" long. Ed..





Manson has 416 HE and 408 HE prints, as well as 375 HE
He can also make you a resize die reamer from that info.
We got 700 cases in 416 and one more pass if 408s wanted, ,
Going to do lot more cases for these 2 sizes also,
Questions, PM or email. ph 989-644-5228..

Here are final specs for 416 HE.
Length 3.32",  belt diameter  ,655",  base dia  .635" ,
length base to to shoulder 2.860" , 30 deg shoulder.Ed
Pages: [1] 2 3 ... 10